attackvast.blogg.se

1. #Mla tour xdream putter review full
2. #Mla tour xdream putter review code
3. #Mla tour xdream putter review plus
4. #Mla tour xdream putter review series

I’ll get into the actual performance of it later, but for now I’ll say that there’s something comforting about the shape.īeyond the alignment feature, the XDream is a midsized, modern mallet. Both the stark contrast with the black body and the unusual shape make it the dominant visual feature. When you place the MLA Golf XDream at address, your eye is immediately drawn to the white alignment feature near the top line. MLA stands for Multiple Line-detector Activation, and they claim that this patented technology will “revolutionize your putting.” We put it to the test to see if that claim has merit Looks I’ve read a lot of stories about how different putters improve your aim but never anything remotely like MLA’s. I’ve been writing about golf equipment for nearly ten years. If you liked this post, please let us know in the comments section below.The MLA GolfTour XDream putter is a modern mallet with a unique, effective alignment aid.

#Mla tour xdream putter review code

Wanna get started on your own murdered out flat stick using one our MLA putters? For a limited time take 15% off all MLA Putters >$199, use code "DAD" at checkout. Let it dry for an hour and you've just built one badass murdered out putter! Luckily, our Twitter buddy, Enrique, bailed us out by suggesting we remove the shrink wrap from the putter 1/2" shorter than the grip and push like hell! As instructed, we removed the tape, cut the shrink wrap back 9.5" because our grip is 10", re-taped the shaft and pushed like hell! It went on with some major oomph!įinally, take your normal putter stance and gently twist the grip until it's lined up with the head.

#Mla tour xdream putter review plus

The wrap plus the layer of tape was too thick for the grip to go on the shaft. Then, pour the contents of the grip over the tape and quickly, yet smoothly, push the grip onto the shaft. Fill the inside of the grip with the liquid, keeping your finger on the hole at the end of the grip. Twist the excess tape, and stuff it into the end of the shaft. Then place your tape on the club and carefully roll it around the shaft making sure there are no wrinkles. Measure your tape so it's at least as long as your putter grip. We also liked how the green accents in our grip matched up to the green paint on the bottom of our putter. To give our putter a really mean look, we decided to use this limited edition skull grip from SuperStroke. Now we need to add our new grip, any black grip will do.

This gave the wrap a much cleaner, finished look at the bottom. We took a small ring of shrink wrap, placed it over the existing wrap where it meets the head and shrunk it on the shaft. We had a very difficult time getting the wrap to meet the putter head perfectly without leaving some of the chrome shaft exposed. It should look like this when you're finished. Continue until the shrink wrap is tight all the way around the club.

#Mla tour xdream putter review full

Be sure to spin the putter to shrink the full circumference as you work your way up the shaft. Now use the heat gun to gradually shrink the wrap.

Feed the putter shaft through the shrink wrap getting as close as possible to the head of the putter and 1" longer than the grip end of the shaft. Once the shaft is smooth, cut your shrink wrap (We found ours on Amazon Here) approximately 1.5-2" longer than your putter shaft. Any nicks, dings or remaining tape/stickers will show under the shrink wrap. Then, using your fine sand paper, go up and down the shaft to make sure it is smooth. You will also want to remove any manufacturer stickers that might be on the shaft. If you don't want to invest in a heat gun, a blow dryer on high may be adequate. We got our heat gun at Harbor Freight for $8.99 using their 20% off coupon. Next, use your heat gun to loosen the old grip tape and peel it off. Just be careful and push the blade away from you when cutting the grip.

You can replace the razor blade with a hook blade, but it's not necessary. The first step is to remove your old putter grip using your utility knife. The black face lends itself well to our project and, as you will see later, matches up perfectly to the grip we chose! Golf Gear Box sells the full line of MLA putters here.

#Mla tour xdream putter review series

Since we just got some new demo MLA putters in stock, we decided to use our old Tour Series XDream for this project. Regripping kit (utility knife, piece of 2 sided tape, mineral spirits, vice) Here is what you will need to for this project. Well with this conversion method you don't need any of those tools or skills to create your very own murdered out flat stick. The only problem is we don't have any putter refinishing skills or equipment. We love the look of murdered out (black) putters we've seen during PGA telecasts and posted on Twitter & Instagram and decided we wanted one of our own.